Hi All
just noticed tonight the laser is cutting twice round each item, i have looked at the forum and it was surgested that it was the import, so i produced a square in lasercut 5.3 only which cut twice. Dont think i have changed anything. What would cause this.
thanks
Paul
laser cutting twice
-
woodturningbypaul
- Posts: 17
- Joined: Mon Dec 19, 2011 1:01 pm
- Contact:
Re: laser cutting twice
Daft question - on the panel on the laser - is Pieces set to 1?
Best
Dave
Best
Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Re: laser cutting twice
Another thing I just thought of - last column on the cut/engrave speed/power settings there is 'Times' - any chance this has been set to 2?
Dave
Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
-
woodturningbypaul
- Posts: 17
- Joined: Mon Dec 19, 2011 1:01 pm
- Contact:
Re: laser cutting twice
yep
never noticed that before
thanks
Paul
never noticed that before
thanks
Paul
Re: laser cutting twice
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
-
woodturningbypaul
- Posts: 17
- Joined: Mon Dec 19, 2011 1:01 pm
- Contact:
Re: laser cutting twice
sorry was replying to your question about the control panel
both the panel and the last column are both set to one
Paul
both the panel and the last column are both set to one
Paul
Re: laser cutting twice
Can't think what else at the moment then. Will have a think 
Dave
Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Re: laser cutting twice
If you draw a single line does it do that twice too?
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
-
woodturningbypaul
- Posts: 17
- Joined: Mon Dec 19, 2011 1:01 pm
- Contact:
Re: laser cutting twice
sorted !!
I have rechecked all the setting, the first piece I cut tonight I set the power and the speed and i guess tabbed onto the overlap which was set to 72, which i had not noticed. I reset that back to .1.
thanks for all your help dave much appreciated.
Paul
I have rechecked all the setting, the first piece I cut tonight I set the power and the speed and i guess tabbed onto the overlap which was set to 72, which i had not noticed. I reset that back to .1.
thanks for all your help dave much appreciated.
Paul
Re: laser cutting twice
No worries - glad you sorted it
Best
Dave
Best
Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Who is online
Users browsing this forum: No registered users and 10 guests