Hi guys
Im currently updating my 6090 to a cloudray system. RuiDa RDC 6432G. Has anyone done this and is there a walk through?
The its all up and running connection wise, just trying to figure out the limit as the head keeps running into the side and laser parameters for cutting.
Many thanks
Search found 47 matches
- Wed Jan 10, 2024 2:57 pm
- Forum: Help or advice required please
- Topic: laser controller upgrade
- Replies: 0
- Views: 2091
- Tue Jan 19, 2021 4:31 pm
- Forum: General Discussion
- Topic: Air assist
- Replies: 3
- Views: 4775
Re: Air assist
Hi Dave
The little bugger has worked hard these past years. I did go to an aquatics place to find a better one. They said the one I had was more powerful than what they supplied which was strange.
Whats the model of the air comp you have?
Rich
The little bugger has worked hard these past years. I did go to an aquatics place to find a better one. They said the one I had was more powerful than what they supplied which was strange.
Whats the model of the air comp you have?
Rich
- Tue Jan 19, 2021 2:31 pm
- Forum: General Discussion
- Topic: Air assist
- Replies: 3
- Views: 4775
Air assist
Hi guys Hope you are all well. Not been on for a while I have a 6090 and still on the original air assist. Think it's going to give up soon so thought i'd catch it before hand (its 7 years old so had some hammer) Can anyone recommend a bigger and better air assist pump for me? Many thanks in advance...
- Tue Aug 30, 2016 4:50 pm
- Forum: Help or advice required please
- Topic: Final mirror alignment
- Replies: 3
- Views: 4420
Re: Final mirror alignment
Thanks Dave worked a treat
- Sun Aug 28, 2016 6:40 pm
- Forum: Help or advice required please
- Topic: Final mirror alignment
- Replies: 3
- Views: 4420
Final mirror alignment
Hi Guys Trying to get my final mirror right is proving a pain. Im cutting 5mm acrylic and the cut lines are fine across ways but when I do tests with vertical down lines I can see that the acrylic is slightly angled. All the other mirrors are fine with tests and dots. Ive managed to get the line a l...
- Sun Aug 28, 2016 6:20 pm
- Forum: Help or advice required please
- Topic: 6mm Birch Plywood
- Replies: 6
- Views: 7176
Re: 6mm Birch Plywood
Couldn't agree more with Slec. Used them for years and never had any issues
- Sun Aug 28, 2016 6:18 pm
- Forum: Help or advice required please
- Topic: Settings for cutting acrylic please
- Replies: 7
- Views: 10979
Re: Settings for cutting acrylic please
Hi there Dreamcatcher I have a 60w tube and and can cut 3mm cast on speed 20 power 55 As for cutting (this is what I do) you can cut with the plastic coating off but I like to play it safe and cut with the protective film on. If i'm cutting from a big sheet I like to hold it down with some sort of c...
- Mon Jul 11, 2016 8:32 pm
- Forum: General Discussion
- Topic: LS6840 Recommended Settings
- Replies: 3
- Views: 5825
Re: LS6840 Recommended Settings
I like to use poplar. Its lighter than ply The settings i use For 3mm Poplar speed 28 power 45 (these were on my old tube which i've just replaced last week so could definitely drop the power) For 3mm acrylic i use speed 10 power 30 (this is a setting i know has always worked so i don't bother chang...
- Sat Nov 21, 2015 7:05 pm
- Forum: Help or advice required please
- Topic: Ez-usb fx2
- Replies: 7
- Views: 7576
Re: Ez-usb fx2
I'll give it another go and see if it works.
Many thanks for the advice
Richard
Many thanks for the advice
Richard
- Sat Nov 21, 2015 6:46 pm
- Forum: Help or advice required please
- Topic: Ez-usb fx2
- Replies: 7
- Views: 7576
Re: Ez-usb fx2
Hi tom
What do I right click on. I've done every type of driver update and it comes up with can't install drivers
Many thanks Richard
What do I right click on. I've done every type of driver update and it comes up with can't install drivers
Many thanks Richard