Search found 9 matches
- Sun Nov 24, 2013 10:18 am
- Forum: Help or advice required please
- Topic: 3060 vs. 3050 vs. ...
- Replies: 31
- Views: 28355
Re: 3060 vs. 3050 vs. ...
Ah, the 'luxury' one
- Sun Nov 24, 2013 9:30 am
- Forum: Help or advice required please
- Topic: 3060 vs. 3050 vs. ...
- Replies: 31
- Views: 28355
Re: 3060 vs. 3050 vs. ...
Hi Dave,
Is the Chinese junk one you have one of those they are selling on ebay for £400ish? May be interested if you don't think you will use it?
Thanks
Matt
Is the Chinese junk one you have one of those they are selling on ebay for £400ish? May be interested if you don't think you will use it?
Thanks
Matt
- Sat Nov 23, 2013 11:12 am
- Forum: Help or advice required please
- Topic: 3060 vs. 3050 vs. ...
- Replies: 31
- Views: 28355
Re: 3060 vs. 3050 vs. ...
Have you used the 3030 router from HPC? Might get one of those I think.
- Sat Nov 23, 2013 11:11 am
- Forum: Help or advice required please
- Topic: 3060 vs. 3050 vs. ...
- Replies: 31
- Views: 28355
Re: 3060 vs. 3050 vs. ...
Thanks again Dave, I will have a look at the routers for that kind of work, it makes sense. I am cutting 4mm MDF on the 3020 at 35%/9mms and it seems to be the right speed/quality. I diy'd a chiller involving a filter and swapping freezer blocks every 2 hours and it keeps it < 15 degrees. Can't beli...
- Tue Nov 19, 2013 4:02 pm
- Forum: Help or advice required please
- Topic: 3060 vs. 3050 vs. ...
- Replies: 31
- Views: 28355
Re: 3060 vs. 3050 vs. ...
Thanks Dave,
Only a little bit out with an 80w then
What would be suitable for 9mm? That would probably be thick enough.
Cheers,
Matt
Only a little bit out with an 80w then
What would be suitable for 9mm? That would probably be thick enough.
Cheers,
Matt
- Tue Nov 19, 2013 2:58 pm
- Forum: Help or advice required please
- Topic: 3060 vs. 3050 vs. ...
- Replies: 31
- Views: 28355
Re: 3060 vs. 3050 vs. ...
That was a handy topic, came looking for pretty much exactly the same thing :) Lots of 3mm MDF to cut. I had finally decided on the 6840 but have just been asked about cutting 15-20mm MDF. Presumably that would that be way too thick for this and I would need to look at the 6090 or even something wit...
- Tue Nov 12, 2013 9:40 pm
- Forum: Help or advice required please
- Topic: Usage estimate
- Replies: 3
- Views: 4175
Re: Usage estimate
Thanks Dave It is all in great condition and cuts fine generally. Only thing I have noticed is that if I am cutting for an hour or so (5/10 mins at a time over say 3 hours), the cutting depth gradually decreases so I have to increase the power to maintain the same level (at that speed). Could this b...
- Tue Nov 12, 2013 9:14 pm
- Forum: Help or advice required please
- Topic: Usage estimate
- Replies: 3
- Views: 4175
Usage estimate
Hi, I recently purchased a LS3020 second hand to try some ideas out (already at the point where it is proven and need something bigger!). The person I had bought it off said it had only had about 100 hours use at < 25% power. Is there any way I can verify this? Only thing I could think of was cuttin...
- Thu Nov 07, 2013 10:51 am
- Forum: Help or advice required please
- Topic: Upgrading Machine
- Replies: 6
- Views: 6650
Re: Upgrading Machine
Hi,
I am also in a similar position, possibly looking to upgrade the LS3020.
But I just wondered where the best place to sell my existing one would be, do HPC take part ex against larger models?
Thanks,
Matt
I am also in a similar position, possibly looking to upgrade the LS3020.
But I just wondered where the best place to sell my existing one would be, do HPC take part ex against larger models?
Thanks,
Matt