I guess it could be but I have not seen temp issues on my machines and the workshop get quite hot so I suspect it is more likely to be a connection issue with the plugs on the pad to the MCB. It may also be a cold joint on the boards somewhere....
Best
Dave
Search found 1614 matches
- Fri Jun 28, 2024 7:56 am
- Forum: Help or advice required please
- Topic: System won't start
- Replies: 4
- Views: 488
- Thu Jun 27, 2024 1:57 pm
- Forum: Help or advice required please
- Topic: System won't start
- Replies: 4
- Views: 488
Re: System won't start
Does the head move and datum? It could be the switches are sticking so the MCB is not getting feedback to where the head is but it could also be something like a loose connector on the board (MCB).
Best
Dave
Best
Dave
- Fri Jun 14, 2024 3:54 pm
- Forum: Help or advice required please
- Topic: Lasercut5.3 dongle not working. Driver? Config?
- Replies: 2
- Views: 280
Re: Lasercut5.3 dongle not working. Driver? Config?
Hi James,
Give HPC a call - they may have an early copy still and you will need the config file for the 6090 if you don't have it.
Best
Dave
Give HPC a call - they may have an early copy still and you will need the config file for the 6090 if you don't have it.
Best
Dave
- Mon Dec 04, 2023 11:37 am
- Forum: General Discussion
- Topic: 3020 Intermittent cutting
- Replies: 4
- Views: 2974
Re: 3020 Intermittent cutting
Check the connections to the tube to make sure there is no arching.
Depending on how the tube has been used and looked after it may only last a short time if you are unlucky.
Best
Dave
Depending on how the tube has been used and looked after it may only last a short time if you are unlucky.
Best
Dave
- Thu Nov 30, 2023 4:26 pm
- Forum: General Discussion
- Topic: 3020 Intermittent cutting
- Replies: 4
- Views: 2974
Re: 3020 Intermittent cutting
Hi Chris.
If the tube is overheating it can stop cutting until it cools down - can you explain a bit more when it stops and if it starts again?
Best
Dave
If the tube is overheating it can stop cutting until it cools down - can you explain a bit more when it stops and if it starts again?
Best
Dave
- Sun Jul 16, 2023 8:41 am
- Forum: General Discussion
- Topic: 3020 laser issue
- Replies: 1
- Views: 1617
Re: 3020 laser issue
I had this once and it turned to be the tube.
Best
Dave
Best
Dave
- Tue Jun 06, 2023 4:22 pm
- Forum: Help or advice required please
- Topic: problems with cutting, parts cutting wrong sizes
- Replies: 7
- Views: 2902
Re: problems with cutting, parts cutting wrong sizes
So array is this option Screenshot 2023-06-06 161350.png so cuts the same part x number of times. This would exclude any anomalies in the file and if all parts cut the same then it is more chance to be a setting issue. If all parts are different it could be mechanical. May be worth exporting the CFG...
- Tue Jun 06, 2023 2:46 pm
- Forum: Help or advice required please
- Topic: problems with cutting, parts cutting wrong sizes
- Replies: 7
- Views: 2902
Re: problems with cutting, parts cutting wrong sizes
So is it the same part set up as an array? If you create a simple box and cut that in an array does it do the same?
- Tue Jun 06, 2023 2:31 pm
- Forum: Help or advice required please
- Topic: problems with cutting, parts cutting wrong sizes
- Replies: 7
- Views: 2902
Re: problems with cutting, parts cutting wrong sizes
Check on the control pad on the machine that the setting are set correct. Most options should be 100% as the software overrides - and strange numbers in the CP can make it do strange things.
- Sun Mar 19, 2023 6:14 pm
- Forum: Help or advice required please
- Topic: Diameter of laser?
- Replies: 1
- Views: 3293
Re: Diameter of laser?
Not that I know of without using different lens or beam expander but I am not sure that is possible on the smaller machines. How large is it? You can try doing a ramp test to perfect the focus on the machine which may help. Also make sure the lens is right way up for the focus tool (cupped surface u...