Help needed please

Moderators: HPC, Daven

Post Reply
Susie
Posts: 36
Joined: Sat Aug 20, 2011 7:52 pm
Contact:

Help needed please

Post by Susie »

Hi There
I am a complete novice so please bear with me! I have a Ls 30-20 I have set up the machine but cannot seem to get to grips with the design side and how to start cutting!
When I import a file I cannot click the pick button so the scan tool shows, also I cannot find my model in the place where you surpose to put it ( Factory Artsign) Model ( Ls-3020 is not there) Do I have to number each piece that I want cutting out.
So sorry if I seem a complete twit! Can I use Newlydraw with XP.
Any help would be great.
Susie.
Daven
Posts: 1632
Joined: Fri Oct 15, 2010 6:44 pm
Location: Devon
Contact:

Re: Help needed please

Post by Daven »

Hi Susie,

What disk did you use to install Newlydraw? Sounds daft but the version that used to be shipped with the LS3020 marked 'HPC Installation software' did not work so you need the Newlydraw disk.
Susie wrote:Do I have to number each piece that I want cutting out.
You don't as such the numbers are for the cut order so you can do the small inner bits first if required.

XP is recommended so you should be ok there ;-)

Cheers

Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
PhillyDee
Posts: 622
Joined: Fri Apr 08, 2011 12:25 am
Contact:

Re: Help needed please

Post by PhillyDee »

When you first import a dxf file, you will need to click the SPLIT button at the top right in the toolbar. This will split it into individual elements. Then you can select what you need from the menus.
http://www.tmbelectronics.com - Electronics, tools, hobby tools, power tools, and much more!

An ex LS3020 user now playing with an LS6840PRO (60W) and an LS1290PRO (80W)
Susie
Posts: 36
Joined: Sat Aug 20, 2011 7:52 pm
Contact:

Re: Help needed please

Post by Susie »

Do I have to connect the laptop to the laser when i install the Newly draw cd?
Susie
Posts: 36
Joined: Sat Aug 20, 2011 7:52 pm
Contact:

Re: Help needed please

Post by Susie »

Is windows 7 ok to use
PhillyDee
Posts: 622
Joined: Fri Apr 08, 2011 12:25 am
Contact:

Re: Help needed please

Post by PhillyDee »

I would look here for windows 7
http://www.laserscript.co.uk/phpBB3/vie ... lling#p439

And here is a quick start for the LS3020
http://www.laserscript.co.uk/phpBB3/vie ... ?f=9&t=344
http://www.tmbelectronics.com - Electronics, tools, hobby tools, power tools, and much more!

An ex LS3020 user now playing with an LS6840PRO (60W) and an LS1290PRO (80W)
Daven
Posts: 1632
Joined: Fri Oct 15, 2010 6:44 pm
Location: Devon
Contact:

Re: Help needed please

Post by Daven »

Susie wrote:Is windows 7 ok to use
XP is recommended, ND will run but I have not got the device drivers to run on Win 7
Susie wrote:Do I have to connect the laptop to the laser when i install the Newly draw cd?
No, but you do when installing the drivers.

Cheers

Dave
Using two LS3060's and an ex 3020 user
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Susie
Posts: 36
Joined: Sat Aug 20, 2011 7:52 pm
Contact:

Re: Help needed please

Post by Susie »

Ok I will install properly and have another go. Thanks Susie
Spooky
Posts: 1291
Joined: Mon Apr 26, 2010 10:17 pm
Contact:

Re: Help needed please

Post by Spooky »

afaik there aren't any drivers for ND for windows 7, the lasercut ones have been out for a little while but lasercut is a much more expensive package.

best wishes

Dave
Please note I am not employed by HPC, any advice or recomendations I give are based on my own experience and are not necessarily the same as HPC's. First point of contact on any hardware issues should be with HPC
Dave@OpticalPower.co.uk
Susie
Posts: 36
Joined: Sat Aug 20, 2011 7:52 pm
Contact:

Re: Help needed please

Post by Susie »

Getting there! Can I use publisher to design and change the file Jpeg? Also LS3020 is not on the dropdown menu.
Thanks
Post Reply

Who is online

Users browsing this forum: Ahrefs [Bot] and 1 guest