No problems and welcome
Best
Dave
Search found 1611 matches
- Thu May 13, 2021 10:16 am
- Forum: Login and say Hello
- Topic: Hello and Help
- Replies: 3
- Views: 6638
- Thu May 13, 2021 8:36 am
- Forum: Login and say Hello
- Topic: Hello and Help
- Replies: 3
- Views: 6638
Re: Hello and Help
Hi Zoe - I do not use Mac's or lightburn so can't help but I bet if you called HPC someone will help you out
Best
Dave
Best
Dave
- Wed May 12, 2021 4:40 pm
- Forum: Help or advice required please
- Topic: LaserCut 5.3
- Replies: 3
- Views: 4633
Re: LaserCut 5.3
file, Machine Options, worktable
- Fri May 07, 2021 8:54 am
- Forum: Help or advice required please
- Topic: bed raise/lower
- Replies: 2
- Views: 4142
Re: bed raise/lower
Yep that is the same on mine - if you press datum it will re-set back to the top on it's own.
The speed is slow though - should be quicker than that - make sure the belt isn't slipping.
Best
Dave
The speed is slow though - should be quicker than that - make sure the belt isn't slipping.
Best
Dave
- Mon Apr 26, 2021 5:48 pm
- Forum: General Discussion
- Topic: Ls6090 axis misbehaving
- Replies: 1
- Views: 4608
Re: Ls6090 axis misbehaving
Give HPC a call - it will be quicker than trying to troubleshoot here
Best
Dave
Best
Dave
- Mon Apr 12, 2021 9:07 am
- Forum: Help or advice required please
- Topic: Engraving speeds and power on HPC 6090 pro
- Replies: 3
- Views: 4721
Re: Engraving speeds and power on HPC 6090 pro
No problems - DPI = dots per inch - so resolution.
In Lasercut 5.3 - double click on the speed power and set scan gap there
Best
Dave
In Lasercut 5.3 - double click on the speed power and set scan gap there
Best
Dave
- Mon Apr 12, 2021 7:52 am
- Forum: Help or advice required please
- Topic: Engraving speeds and power on HPC 6090 pro
- Replies: 3
- Views: 4721
Re: Engraving speeds and power on HPC 6090 pro
More speed = less darker/deep Less power = same as above Less DPI (Scan gap) = same as above So increase speed and reduce power and check scan gap settings. Too much speed is not good so check manual or give HPC a call, I normally keep to less than 400 mm/s Scan gap setting can be found here http://...
- Sat Apr 10, 2021 7:04 pm
- Forum: Help or advice required please
- Topic: Blocked Output coupler
- Replies: 7
- Views: 6009
Re: Blocked Output coupler
I use chlorine granules you can buy for hot tubs at DIY sheds - just a teaspoon full seems to help every few months.
Best
Dave
Best
Dave
- Mon Apr 05, 2021 11:02 am
- Forum: Help or advice required please
- Topic: Old HPC LS3040 Software/Driver issues
- Replies: 3
- Views: 5107
- Mon Apr 05, 2021 8:32 am
- Forum: Help or advice required please
- Topic: Old HPC LS3040 Software/Driver issues
- Replies: 3
- Views: 5107
Re: Old HPC LS3040 Software/Driver issues
Hi Chris - you will need the drivers for the key as well - I will email them over
Best
Dave
Best
Dave