Search found 24 matches

by khumbu5
Tue Jul 01, 2014 10:11 am
Forum: Help or advice required please
Topic: Beam width too wide on horizontal cut...
Replies: 1
Views: 2961

Beam width too wide on horizontal cut...

Another one for you gents... I'm putting a line round a design on some oak using a cut. The problem is that the horizontal lines of this square are quite a lot wider than the vertical. The vertical is about what it should be in width but the horizontal line must be close to 0.7mm wide! Any suggestio...
by khumbu5
Tue Jul 01, 2014 10:06 am
Forum: Help or advice required please
Topic: 6090 has lost its Datum...I think!
Replies: 6
Views: 7302

Re: 6090 has lost its Datum...I think!

No, it goes back to its position with no crashing...
by khumbu5
Mon Jun 30, 2014 2:45 pm
Forum: Help or advice required please
Topic: 6090 has lost its Datum...I think!
Replies: 6
Views: 7302

Re: 6090 has lost its Datum...I think!

Sensors all checked and working fine. It also appears it has no 'Soft stop' any more...

Any more advice guys?
by khumbu5
Mon Jun 30, 2014 12:50 pm
Forum: Help or advice required please
Topic: 6090 has lost its Datum...I think!
Replies: 6
Views: 7302

Re: 6090 has lost its Datum...I think!

Thanks for that. I have proximity sensors and would be surprised if both were faulty but will tick it off as a process of elimination.

Ta
by khumbu5
Mon Jun 30, 2014 10:07 am
Forum: Help or advice required please
Topic: 6090 has lost its Datum...I think!
Replies: 6
Views: 7302

6090 has lost its Datum...I think!

Morning everyone, I have a LS6090 which has recently started to behave a bit strangely. Others use this machine so can't account for idle thumbs but here goes... Firstly when I used to switch the machine on the head used to automatically find its datum by going up to the top right hand corner of the...
by khumbu5
Thu May 02, 2013 1:03 pm
Forum: Help or advice required please
Topic: Corel Draw X6
Replies: 10
Views: 13442

Re: Corel Draw X6

Thanks for your feedback. I think for the sake of £53 I'll bite the bullet and get it. Just seems ridiculously cheap compared to the full version. I'm looking for the catch!
by khumbu5
Thu May 02, 2013 12:44 pm
Forum: Help or advice required please
Topic: Corel Draw X6
Replies: 10
Views: 13442

Re: Corel Draw X6

Like wise, thats what I'm used to with AI and it works well for me.
Have you ever had the need to import new fonts into X5?
by khumbu5
Thu May 02, 2013 12:18 pm
Forum: Help or advice required please
Topic: Corel Draw X6
Replies: 10
Views: 13442

Re: Corel Draw X6

That's good to know. Is your X5 a home edition?
by khumbu5
Thu May 02, 2013 12:06 pm
Forum: Help or advice required please
Topic: Corel Draw X6
Replies: 10
Views: 13442

Corel Draw X6

Hi, currently using Adobe Illustrator CS6 at work but want to buy CorelDraw X6 home and student edition for personal use at home then interface with our 6090, lasercut 5.3, etc. Am I likely to encounter any problems with doing this? Also, Is it possible to import new fonts into X6 as there is a limi...
by khumbu5
Fri Apr 12, 2013 12:56 pm
Forum: General Discussion
Topic: Laserply in the south east?
Replies: 6
Views: 8332

Re: Laserply in the south east?

Thank you Pedro, apologies for the late reply, been away for a bit.
Certainly my best lead so far!