Search found 174 matches

by Pedro_Hernandez
Sun Feb 19, 2017 2:33 pm
Forum: Help or advice required please
Topic: Need Vista 32 bit USB Drivers 3020 ND
Replies: 3
Views: 4724

Re: Need Vista 32 bit USB Drivers 3020 ND

Cheers Dave HPC kindly emailed me a link to a download of the drivers, however it didn't fix the issue and was still getting the port error message and laptop dialogue message USB device not recognised pop up. The day before my nozzle cone dropped and fouled on the lip of the aluminium table when se...
by Pedro_Hernandez
Fri Feb 17, 2017 12:00 pm
Forum: Help or advice required please
Topic: Need Vista 32 bit USB Drivers 3020 ND
Replies: 3
Views: 4724

Need Vista 32 bit USB Drivers 3020 ND

Morning All My laptop has been playing up and had sone USB connectivity issues, i've accidently deleted my 3020 drivers and to add insult to injury my laptops CD drive has packed up so cannot run from disc. If anyone can email them over to me it would be much apreicated. TIA Pedro peter@hearnmade.co...
by Pedro_Hernandez
Sat Jan 07, 2017 12:13 pm
Forum: Help or advice required please
Topic: Is Lasercut or Newly draw single user Licence ?
Replies: 2
Views: 3846

Is Lasercut or Newly draw single user Licence ?

Morning

If.selling on an HPC machine can the software and dongle just be passed or is the software single use and the new owner have to purchase a new licence? .

Cheers

Pedro
by Pedro_Hernandez
Mon Dec 19, 2016 10:14 am
Forum: Help or advice required please
Topic: Double Sided woes! Some Advice needed
Replies: 2
Views: 4068

Re: Double Sided woes! Some Advice needed

You could always cut a jig , allowing adequate distance between objects, so engraves then the cut outs drop down into a clear space, ensure that it is open front to back to allow the vaporised acrylic to extract out. If you have a tray/bit of card under just pull it out and remove cuts outs .Clean u...
by Pedro_Hernandez
Sat Dec 17, 2016 5:17 pm
Forum: Help or advice required please
Topic: 3020 carriage stoppin/freezing during engrave
Replies: 5
Views: 6188

Re: 3020 carriage stoppin/freezing during engrave

Do you mean moves when it's on Dave ? :D my carriage has always moved quite freely with machine turned off!, I'll check the homing sensors and carriage blade as well I've had it do weird things before now and it's either been a build up of crud on the blade or sensor got a bit of debris on on the ra...
by Pedro_Hernandez
Sat Dec 17, 2016 9:47 am
Forum: Help or advice required please
Topic: 3020 carriage stoppin/freezing during engrave
Replies: 5
Views: 6188

Re: 3020 carriage stoppin/freezing during engrave

Maybe Dave,however I've never had a problem with this file,prob sent it down about 150 plus times with no problem. Only exception this last time is that I've used the "select all" command before sending,and also had another file minimised that I use for an alignment check but was still sel...
by Pedro_Hernandez
Sat Dec 17, 2016 2:31 am
Forum: Help or advice required please
Topic: 3020 carriage stoppin/freezing during engrave
Replies: 5
Views: 6188

3020 carriage stoppin/freezing during engrave

Good Morning All This has never happend to me before but on three seperate occasions during a 3-4 hour period the laser carriage has jsut stopped, not always in the same place but the machine remains on and carriage locked in place with no laser output with the useual Logic port error messages when ...
by Pedro_Hernandez
Tue Dec 13, 2016 10:19 pm
Forum: Help or advice required please
Topic: Wool felt or synthetic?
Replies: 8
Views: 9693

Re: Wool felt or synthetic?

I think you need to put it into context, we're not talking about any discernable levels of HCN being produced laser cutting and engraving sheeps wool felt. Maybe a warehouse or factory full of the stuff going up would pose a significant risk, which is more relevant to the link posted. As for the sme...
by Pedro_Hernandez
Mon Dec 05, 2016 9:42 pm
Forum: General Discussion
Topic: Aligning after etching
Replies: 4
Views: 7877

Re: Aligning after etching

Did you ever solve this issue Kris ? My 3020 has never aligned a profile cut with an engrave from new,,I've always run an engrave then reset X,Y to home and then used the send to X,Y command and sent the same file but with just the profile cut part of the file. I think it's just the limitations of a...
by Pedro_Hernandez
Sun Dec 04, 2016 8:18 am
Forum: General Discussion
Topic: Old tubes disposal
Replies: 2
Views: 4645

Old tubes disposal

Morning All

Bit of a weird question, I've just gone back to work in athe same School I was at nearly 5 years.ago and they've got two old knackered 1290 tubes,can I just chuck them in the skip or are there any restrictions or control of disposal.

Cheers

Pedro